日文工程師

1.客戶廠區端駐廠工作，負責機台裝機、保養維護及其他客戶服務。 

2.廢氣處理設備及相關事業。 

3.機台維修保養及問題排除。 

4.不需輪班，需On call ，平均每週1-2次 。 

5.夜間/假日值班津貼。 

6.依年度績效考核調薪。 

7.依能力核薪，值班津貼、加班津貼另計。 

國內外多家知名半導體廠皆有採購。 

歡迎各領域伙伴加入我們的團隊。

1.Chiller(溫控機台)裝移機 

2.需輪值on call  

3.售後服務(如：客戶拜訪、產品狀況了解) 

4.回覆顧客應用技術的問題，回饋給相關單位，並提供產品技術諮詢 

5.無塵室作業

1、裝機、驗機、與機台之維修改造。 

2、機台售後服務事項之辦理。 

3、與工廠及客戶端之協調、問題反應與解決。 

4、SOP之撰寫。 

5、需配合國外出差、加班、輪班。 

※出差津貼、輪班津貼另計

We are looking for a talented Senior Engineer ( with EOS, DV, DVP or Sabre3D experience will be great) to become a part of our Global Flexible Workforce Team. 

1. High travel rate: 75％ of the time, including international travel (could over 50％). 

2. Comply with all safety procedures and demonstrate safety consistently as a value. 

3. Complete the installation by consistent result with specified cycle times. Control the spending within budget. Train the local engineer to have same knowledge and skills. 

4. Perform all standard installation activities from system move-in (Tier0), hardware setup (Tier1), process tuning (Tier2) independently.  

5. Be able to run upon shift model as needed and perform routine preventative maintenance within established timeframes. Complete quality repairs.  

6. Plan assimilation & Training: Train ramping operations (SOP, EHS), product knowledge assimilation, and conduct cross-product training during off-ramping. 

7. Organize startup lesson learn with overall account team. 

8. Work with site management to drive the MFG (manufacturing) quality improvement plan. 

9. Diagnose and resolve technical problems. Use training and experience to identify process and software or hardware related system problems. 

10. Assume responsibility to follow customer ground rules, regulations, and for complete customer satisfaction within work area. Assist in planning, communicating, and coordinating the installation plans with customer.  

11. Respond to fab issues by communicating with other engineers and participating in escalation conference calls. Apply diagnostic techniques, using of documentation, and test equipment with assistance from senior engineer. May participate in projects to reduce costs and increase uptime.

1. Responsible for providing quality repair and preventive maintenance service of company equipment at customer sites. May install or relocate customer equipment and perform associated start-up and check-out procedures under supervision. 

2. Perform on-site preventive maintenance. Order and replace defective units, components or parts as appropriate. 

3. Troubleshoot equipment problems and conduct diagnostic procedures to isolate problems and take steps to minimize downtime or system interruptions and eliminate equipment malfunctions. 

4. Determine corrective actions required and escalate for assistance and prompt resolution with the support of technically more experienced staff for assistance and guidance when assessing severity of malfunctions and determining corrective actions required. 

5. On the job Training (OJT) to assist with installing and start up and/or relocating equipment at customer’s site. 

6. Remain up to date on equipment/tools through appropriate training, manuals, factory periodicals and other relevant materials. 

7. Execute project action items under direct supervision. 

8. Perform other related duties as assigned by senior FSE / supervisor. 

Leadership 

May Provide on-site instruction to sub-contractors and customers. 

Customer Relation 

1. Professionally represent the company to the customer. Be committed to customer satisfaction and develop good customer relations by maintaining standards of conduct acceptable to both Lam and customers. 

2. Shadow more experienced engineer at customer site.

1.回覆客戶技術的問題，提供蝕刻機台技術諮詢。 

2.提供客戶處安裝、移機、檢修維護保養機台設備。 

3.接聽客戶電話，回應並處理客戶問題、故障排除。  

*可接受手機值班&on call 

*願意轉調至其他據點(新竹、台中、台南、高雄)